|
|
05-17-2011, 03:19 PM
|
#21
|
Montana Master
Join Date: Feb 2005
Location: Haysville
Posts: 4,261
M.O.C. #3085
|
Quote
"Nice job, but how is the heat from the belly to get to the convience center and cargo area? I was told that it was that way to let the heat get to those areas when I was going to do the same thing. Only time I have noticed drafts inside was if I had a cargo door open."
I guess you have a point with the plumbing behind the convience center, but I'd opt for teeing off the 2" duct going to the underbelly and adding a 2" hole in my plywood for that extra run. You are fortunate not to have a draft unless your storage doors are open as most of our belly pans and aluminum lower skirting are not anywhere close to being well sealed. My cargo bay doors don't seal well either as I've replaced the rubber seal twice with it still pinching it out the top length on the street side. A windy day with just a vent open most always gives notice to a draft from under the bedroom steps or from the grill under my fridge (3150RL). I tend to leave a storage door open while setting up, grilling, or what have you in the summer. Hot air just pours into the living area thru the grills mentioned above. As for the storage area ... I don't travel in cold weather with anything in there that would matter. Thanks for pointing out the back of the convience center water lines for others. For me, the wall is staying as I don't use my fiver over the winter, but if I did I'd just drill a 2" hole and tee off the belly duct.
|
|
|
10-06-2011, 12:25 PM
|
#22
|
Montana Master
Join Date: Aug 2004
Location: Asheville
Posts: 502
M.O.C. #1967
|
any of you RK owners have a big whole cut under the cabinet where the hot water heater is, like a 2" circle that lets cold air in? What is the easiest way to seal it?
|
|
|
10-06-2011, 01:25 PM
|
#23
|
Montana Master
Join Date: Sep 2008
Location: Bangor
Posts: 770
M.O.C. #8816
|
I also cover the grills on the step risers from the inside. I cut the silver insulation stuff to fit. I did this when I found out i was cooling the basement, it helped a lot. I used the Insulation in a can Great Stuff to fill the piping holes in the floor under the sinks.
kevin
|
|
|
10-07-2011, 04:44 AM
|
#24
|
Montana Master
Join Date: Jun 2010
Location: Colorado Springs
Posts: 3,335
M.O.C. #10496
|
This is on my winter project list.
__________________
2010 3150RL
LevelUp, Dual 6 volt batteries, Progressive Industries EMS HW50C, Honda EU2000i Generator, Bridgestone Duravis R250 tires, Torklift Glowstep Revolution Stairs, LED Tail lights
2015 RAM 3500 Laramie SRW LB CC Cummins 6.7L Aisin Trans B&W RVK3600
|
|
|
07-12-2018, 08:26 PM
|
#25
|
Montana Fan
Join Date: Aug 2017
Location: Twin Falls, ID
Posts: 211
M.O.C. #20361
|
I know this is an old thread, but I wonder if any could offer feed back as to long term results ? Especially concerning cold weather and the water lines. Also canned foam in the pipe holes? Thanx
__________________
Jim and Barb
Chica and Baby (the fury kids)
2014 3402rl
2017 Ram 3500 6.7 ctd. 4x4 srw
|
|
|
11-07-2021, 01:55 PM
|
#26
|
Montana Fan
Join Date: Mar 2009
Location: Sun Lakes, AZ 85248
Posts: 180
M.O.C. #9174
|
Are you happy with the Great Stuff seal you made around the bathroom sink plumbing where it goes through the floor?
__________________
Carl & Susan G
2021 Montana 3121RL Legacy
2017 Ford F250 6.7 diesel
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|