|
12-02-2022, 01:07 PM
|
#1
|
New Member
Join Date: Aug 2022
Location: O'Brien
Posts: 2
M.O.C. #31442
|
Battery box
Trying to check battery levels. Can't get cover top to clear hydraulic tank. '22 Montana rs 3791. Anyone else have this problem ? Am I missing something or is this another key stone engineering example. Any suggestions before I start undoing a bunch of stuff just to check levels?
Thanks.
|
|
|
12-02-2022, 01:36 PM
|
#2
|
Montana Master
Join Date: May 2019
Location: Alton
Posts: 2,708
M.O.C. #24086
|
Been there done that...
If you look at your hydraulic motor and reservoir, they are mounted to a bracket.
The bracket is mounted to the wall. Undo the front screws of the bracket/wall screws and see if that gives you enough tilt to get the battery box Lid off.
If not take another screw out etc.
Once you do get the lid off, I moved the battery box forward to the front of the compartment. (there are screws in the bottom of the box mounting it to the floor).
__________________
Daryl and Marianne,
2019 3130re 20th Anniversary Edition
2016 F350 Lariat
|
|
|
12-02-2022, 02:20 PM
|
#3
|
Montana Master
Join Date: Oct 2019
Location: Jacksonville
Posts: 2,145
M.O.C. #25165
|
Just to add to what Daryles said, if you do move the box, make sure not to cover up the vent hole in the bottom. Any spilt water or battery acid can drain here as well as allowing the gasses to vent below.
When I went to using 2 golf cart batteries, I removed the original box and made a new one from a Craftsman plastic tote with a sealing lid. The lid clamps on, so it made it easier to check the batteries and add distilled water as necessary.
__________________
Robert & Diana McNeal
2019 Montana Legacy 3791RD 20th Anniversary Edition
2014 F350 4x4 6.7L SRW
|
|
|
12-02-2022, 02:30 PM
|
#4
|
Montana Master
Join Date: Oct 2012
Location: Box Elder
Posts: 4,706
M.O.C. #12947
|
The dealers install the boxes when they install the batteries, so it's not coming from the factory with boxes installed. I upgraded battery size several years ago, so purchased a new box, cut a new drain/vent hole in the floor for the vent nipple, and am able to pull the cover off easily. You can probably just relocate the box you have with a little effort.
__________________
Bob & Becky
2012 3402RL
2012 Chevy 2500HD D/A CC 4WD
|
|
|
12-07-2022, 03:45 PM
|
#5
|
New Member
Join Date: Apr 2019
Location: Jacksonville
Posts: 6
M.O.C. #23902
|
Battery Box
I got tired of having to remove the lid to check water levels. I installed a flow-rite system for 2 batteries along with the hand pump fill. I drilled a hole in the lid to fit the fill hose through and keep a gallon of distilled water in front bay and once a qtr. I attached the hand pump to the fill system and squeeze till hand bulb is hard and done. Takes less than 2 mins to top off water levels. Good luck!!
|
|
|
12-08-2022, 11:14 AM
|
#6
|
Montana Fan
Join Date: Apr 2021
Location: everywhere, USA
Posts: 281
M.O.C. #28634
|
same here
I relocated the battery box so I could get the cover off. Then a few months later I replaced all of the batteries with lithium and removed the box because I didn't need it. Go figure!
__________________
2021 Montana 3761FL, 9 LIFPO4 batteries & 1700 watts of panels w/ Multiplus II 3K inverter and 30amp DC to DC charger from truck. 8k Dexter axles w/ Kodiak disc brakes.
2019 6.7 diesel F350 DRW with Banks derringer and 4"exhaust, airlift bags, 25k B & W Companion hitch, 45 gal. aux. diesel tank and 14k Winch, just in case!
|
|
|
12-08-2022, 05:06 PM
|
#7
|
Montana Fan
Join Date: Dec 2017
Location: Holts Summit
Posts: 123
M.O.C. #20913
|
I believe there is enough give in the plastic box to force the cover off. That’s what I do. I wouldn’t dismantle anything.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|