|
04-30-2022, 11:15 AM
|
#1
|
Montana Fan
Join Date: Jul 2018
Location: Fullerton
Posts: 209
M.O.C. #22148
|
Broken Front Door Hinge
We have noticed recently that our front door to the trailer has been “snapping” when we open and close the door. This morning I took a look and discovered that on the upper hinge, the bracket was broken along with the hinge pin was broken in half. I drilled out the rivets holding the broken bracket in place and have eliminated for now the cracking/snapping sound when the door is opened or closed.
I went online this morning and ordered a new hinge assembly from Trekwood. Hard to take that they want $90 for a new hinge.
Has anyone had a similar issue with their front door and are there any thing I should be aware of when I install the new hinge when it arrives?
Don
__________________
Donjamin & Laurie
Fullerton, CA
2016 Montana Legacy, 3160RL
2015 Ford F-250 SD 4X4
|
|
|
04-30-2022, 01:25 PM
|
#2
|
Montana Fan
Join Date: Dec 2021
Location: Schertz, TX
Posts: 153
M.O.C. #30294
|
Back in the summer of 2020 the friction hinge on our 3850FL caused the door and frame to warp so that the door was almost impossible to close. The hinge never broke at the rivets, but the frame itself warped and the door would hit on the opposite side on the drip rail area above the latch.
I had to have the entire door and frame replaced, fortunately under my extended warranty.
__________________
Clark & Peggy
2022 Montana 3791RD, 800i solar, 2x100ah Battleborn
2017 Ford F350, CC, LB, 6.7, 4x4
|
|
|
05-01-2022, 05:01 AM
|
#3
|
Montana Master
Join Date: Oct 2019
Location: Jacksonville
Posts: 2,137
M.O.C. #25165
|
Quote:
Originally Posted by Donjamin
I went online this morning and ordered a new hinge assembly from Trekwood. Hard to take that they want $90 for a new hinge.
Don
|
Wow, I know Trekwood is very expensive on everything, but you'd think you could get the entire door for $90, not just a hinge.
__________________
Robert & Diana McNeal
2019 Montana Legacy 3791RD 20th Anniversary Edition
2014 F350 4x4 6.7L SRW
|
|
|
05-01-2022, 09:17 AM
|
#4
|
Montana Fan
Join Date: Jun 2019
Location: new river
Posts: 413
M.O.C. #24181
|
__________________
al meyer
3931fb
az
|
|
|
05-01-2022, 03:24 PM
|
#5
|
Montana Fan
Join Date: Jul 2018
Location: Fullerton
Posts: 209
M.O.C. #22148
|
Trekwood wants $920 for the door to our 2016 Montana. All the hardware needed to install the door is extra.
The hinge on Amazon looks similar, ours has two hole per hinge piece that fits the door to the frame. This Amazon picture shows just one hole per hinge segment that anchors door to the frame.
__________________
Donjamin & Laurie
Fullerton, CA
2016 Montana Legacy, 3160RL
2015 Ford F-250 SD 4X4
|
|
|
05-09-2022, 01:41 PM
|
#6
|
Montana Fan
Join Date: Jul 2018
Location: Fullerton
Posts: 209
M.O.C. #22148
|
Our new door hinge arrived this past week while we were vacationing in Utah. It was easy to replace the hinge and align it to the frame. Lippert has a good video on their website on how to replace one of their door hinges. Self tapping screws makes the job easy.
The hinge pin broke as well as one of the door tabs on the hinge. Apparently the gap was not correct between the top of the hinge and the bottom of the hinge and was off my about 3/16 of an inch. Thus, the hinge twisted every time the door was opened and closed. Our door in quiet now and opens and closes easily, and also stays where it is placed.
__________________
Donjamin & Laurie
Fullerton, CA
2016 Montana Legacy, 3160RL
2015 Ford F-250 SD 4X4
|
|
|
07-11-2022, 09:44 PM
|
#7
|
Montana Fan
Join Date: Jul 2019
Location: Mesa
Posts: 277
M.O.C. #24588
|
Quote:
Originally Posted by Ahdmeyer
|
Thanks for posting this amazon link. I saved it on my Amazon wish list in case I too had a hinge failure. Looks to be the same part as the OP ordered from Trekwood.
|
|
|
07-16-2022, 08:00 AM
|
#8
|
Montana Fan
Join Date: Nov 2010
Location: Chatsworth
Posts: 468
M.O.C. #10933
|
I had to replace the bottom hinge last month and ordered on Amazon. I got a box with two hinges for 33$ . I had to use the old hinge extension piece for the screen door but the job was easy after I figured out how to adapt the new hinge and old hinge to hold the screen door. The new hinges were oem from lippert.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|