Journey with Confidence RV GPS App RV Trip Planner RV LIFE Campground Reviews RV Maintenance Take a Speed Test Free 7 Day Trial ×
 

Go Back   Montana Owners Club - Keystone Montana 5th Wheel Forum > MOC Technical Forums > Maintenance
Click Here to Login

Reply
 
Thread Tools Search this Thread Display Modes
 
Old 10-22-2018, 03:44 PM   #1
tomJerram
Seasoned Camper
 
Join Date: Mar 2018
Location: Elmira
Posts: 70
M.O.C. #21376
Wheel lube?

We have a 2014 3625re We bought it used last spring. I can't figure out how to lube the wheels. Attached is a picture of the wheel. It looks like there is se kind of bearing buddy thing there but i dont dare just start prying on the rubber until I know gor sure.

Thanks in advance for the help.
Attached Thumbnails
Click image for larger version

Name:	20181022_173433.jpg
Views:	136
Size:	196.9 KB
ID:	2538  
tomJerram is offline   Reply With Quote
Old 10-22-2018, 04:29 PM   #2
Waricha
Seasoned Camper
 
Join Date: Oct 2017
Location: Blossvale
Posts: 58
M.O.C. #20684
Pry off the rubber cap and there is a zerk fitting there to quick lube the bearings. Don't be surprised if it takes almost a tube of grease per wheel. They never put enough grease in them at the factory. So, if the previous owner never serviced the bearings, they most certainly will need more lube. I lift the wheel of the ground and spin it as I lube the bearings. The old grease will work its way out toward you as you spin it.
Waricha is offline   Reply With Quote
Old 10-22-2018, 05:49 PM   #3
tomJerram
Seasoned Camper
 
Join Date: Mar 2018
Location: Elmira
Posts: 70
M.O.C. #21376
Thanks i thought thst was what was thete but i was afraid to pry it off without knowing. As I get older I get smarter and check before I act. I find that I dont break as much stiff that way.
tomJerram is offline   Reply With Quote
Old 10-28-2018, 06:16 PM   #4
Clyde n Deb
Montana Fan
 
Join Date: Mar 2005
Location: Highlands Ranch
Posts: 462
M.O.C. #3477
None of the RV's I've had have had "Buddy Packers". What you people are recommending with this tube per wheel and 30 strokes are instructions for them. When I greased my Montana more than a few strokes, I had to buy new brakes and seal. A few strokes once a year while jacked up and spinning the wheel is all mine will stand????
Clyde n Deb is offline   Reply With Quote
Old 10-22-2018, 05:46 PM   #5
mlh
Montana Master
 
Join Date: Oct 2004
Location: Salem
Posts: 7,345
M.O.C. #2283
The best thing to is take the wheel and the drum off and service the bearings. They need to be cleaned inspected and repacked. If you aren’t careful you will get grease on the brakes and ruin them with that grease fitting. A pound of grease will more than do all 4 wheels.
Lynwood
mlh is offline   Reply With Quote
Old 10-22-2018, 05:49 PM   #6
BB_TX
Montana Master
 
Join Date: Oct 2006
Location: McKinney
Posts: 6,957
M.O.C. #6433
Those are Dexter EZ Lube axles and are a controversial subject to say the least. Some say never use those zerks or you will have grease soaked brakes. Others say when done properly they work exactly as deigned. Educate yourself about them until you fully understand how they work and then decide for yourself. Key is pumping grease slowly while continuously turning the wheel.

__________________
Bill & Patricia
Riley, our Golden
2007 3075RL (recently sold, currently without)
BB_TX is offline   Reply With Quote
Old 10-22-2018, 06:08 PM   #7
mlh
Montana Master
 
Join Date: Oct 2004
Location: Salem
Posts: 7,345
M.O.C. #2283
Quote:
Originally Posted by BB_TX View Post
Those are Dexter EZ Lube axles and are a controversial subject to say the least. Some say never use those zerks or you will have grease soaked brakes. Others say when done properly they work exactly as deigned. Educate yourself about them until you fully understand how they work and then decide for yourself. Key is pumping grease slowly while continuously turning the wheel.

I fully agree.
Lynwood
mlh is offline   Reply With Quote
Old 12-07-2018, 07:31 AM   #8
WaltBennett
Montana Master
 
WaltBennett's Avatar
 
Join Date: Mar 2013
Location: Hanover
Posts: 1,467
M.O.C. #13325
Quote:
Originally Posted by BB_TX View Post
Those are Dexter EZ Lube axles and are a controversial subject to say the least. Some say never use those zerks or you will have grease soaked brakes. Others say when done properly they work exactly as deigned. Educate yourself about them until you fully understand how they work and then decide for yourself. Key is pumping grease slowly while continuously turning the wheel.


Why people don't think the ones making these don't know what they're talking about is beyond me, but whichever way floats your boat will work. I do what Dexter says to do.
__________________
WaltBennett is offline   Reply With Quote
Old 10-22-2018, 08:24 PM   #9
AZ Traveler
Site Team
 
AZ Traveler's Avatar
 
Join Date: Sep 2017
Location: Oro Valley
Posts: 3,724
M.O.C. #20477
Quote:
Originally Posted by tomJerram View Post
We have a 2014 3625re We bought it used last spring. I can't figure out how to lube the wheels. Attached is a picture of the wheel. It looks like there is se kind of bearing buddy thing there but i dont dare just start prying on the rubber until I know gor sure.

Thanks in advance for the help.
Even if you decide to use the lube system in the future, it would be worthwhile to visually inspect your bearings and brakes at least once since you bought it used. I personally am in the pack by hand camp.
__________________
Zack and Donna plus Millie and Ranger
2018 3160RL

"Life is too short to stay indoors, enjoy the ride!"
AZ Traveler is offline   Reply With Quote
Old 10-22-2018, 09:31 PM   #10
1retired06
Montana Master
 
Join Date: Feb 2012
Location: Lake Gaston
Posts: 8,732
M.O.C. #12156
I also pack by hand.
__________________
Mike and Lorraine
2002 3655 FL, 2005 3650RK
2010 3665RE, 2015 3910FB
F350 crew cab dually 6.7
1retired06 is offline   Reply With Quote
Old 10-22-2018, 10:03 PM   #11
rohrmann
Montana Master
 
rohrmann's Avatar
 
Join Date: Oct 2012
Location: Box Elder
Posts: 4,553
M.O.C. #12947
I used the grease fittings ONCE, exactly as described in the Dexter manual and in warm weather. Six thousand miles later, pulled the drums to check the brakes and had three of the four saturated with grease. Over $500 later, and my labor doesn't count, I had four new backing plate brake assemblies installed, turned all four drums, and had everything back together. I grease the bearings by hand and never use the grease fittings, and never get grease on the brakes. The bearings only need grease on the bearings and all the grease that would end up inside the hub, between the bearings is just a waste if the grease fittings are used. Four new seals and a pound of grease, some rags and solvent cost less than $40, and all four wheels take less than a few hours.
__________________
Bob & Becky
2012 3402RL
2012 Chevy 2500HD D/A CC 4WD
rohrmann is offline   Reply With Quote
Old 10-23-2018, 09:38 AM   #12
ChuckS
Montana Master
 
Join Date: Dec 2017
Location: Mountain Home
Posts: 772
M.O.C. #20949
Since this is a used 2014 and you have no idea what the brakes or bearings and races look like you really need to remove the wheels and drums.. I thin’ the EZ lube system is the worst idea ever.. it circumvents putt8ng eyes on those bearings and races and brakes and attach hardware..

If you are unable to do the work yourself find an RV shop or perhaps trailer shop you can talk with, get an estimate, and let them do the job right..

You don’t want to be along the side of a road with a seized bearing or brake issue..

My 2014 brakes and bearings are done by myself every year.. Still running orig8nal races and bearings and brake shoes because it’s maintained properly.
ChuckS is offline   Reply With Quote
Old 10-28-2018, 02:06 PM   #13
mngn
New Member
 
Join Date: Apr 2016
Location: Waller
Posts: 1
M.O.C. #18504
Dexters

If their true Dexters follow the manufacturers directions. Iíve never had a problem just pump in grease and clean old grease off until clean grease comes out while rotating the wheel.
mngn is offline   Reply With Quote
Old 10-28-2018, 06:14 PM   #14
beeje
Montana Master
 
beeje's Avatar
 
Join Date: Oct 2015
Location: westminster md
Posts: 2,297
M.O.C. #17894
I have had 3 RVs with easy lube. In the last 12 years I have NEVER removed a hub to re-grease. I jack the wheel up and pump in 30-40 pumps or grease while spinning the wheel. First 2 unit had drum brakes. Current one has disc brakes. With the discs, you can see the back side of the hub/grease seal. Think back to the days when you had to repack your cars front bearings. They were not done every year (at least not mine), maybe every 30-40k miles or so.
__________________
2018 Chevy 3500 LTZ Dually Diesel 4x4 CCLB
2011 Montana 3455 SA. 6 point level up. Disc brakes. Curt Q24 Hitch. 5 step glow steps
Progressive EMS. Valterra tank valves. Sailun G637 tires. ARP fridge control. All led lighting. Mor Ryde IS
beeje is offline   Reply With Quote
Old 10-28-2018, 06:17 PM   #15
BB_TX
Montana Master
 
Join Date: Oct 2006
Location: McKinney
Posts: 6,957
M.O.C. #6433
Did I mention controversial?
__________________
Bill & Patricia
Riley, our Golden
2007 3075RL (recently sold, currently without)
BB_TX is offline   Reply With Quote
Old 12-07-2018, 08:57 AM   #16
BB_TX
Montana Master
 
Join Date: Oct 2006
Location: McKinney
Posts: 6,957
M.O.C. #6433
Quote:
Originally Posted by BB_TX View Post
Did I mention controversial?
Oh, yeah. I did.
__________________
Bill & Patricia
Riley, our Golden
2007 3075RL (recently sold, currently without)
BB_TX is offline   Reply With Quote
Old 10-28-2018, 06:43 PM   #17
Graham
Established Member
 
Join Date: Apr 2010
Location: Kamloops
Posts: 37
M.O.C. #10287
I have the EZ lube on my 2010 3465 SE and they have worked just fine. I agree with one of the earlier comments. When I first filled them I had to put a full tube of grease in each wheel. I really wonder why they only put a small amount in from the factory??? Since then I've been topping them up and they have been great. As a precaution, I also use a remote heat sensor when I travel long distances to make sure none of the wheel hubs are heating up.
Graham is offline   Reply With Quote
Old 10-28-2018, 10:30 PM   #18
dieselguy
Montana Master
 
dieselguy's Avatar
 
Join Date: Feb 2005
Location: Haysville
Posts: 4,261
M.O.C. #3085
Sorry EZ Lube testimonial people, but if I had a dollar for ever greased up brake drum caused in some way by the EZ Lube invention that I, my son, or another RV tech I know has witnessed … I could have bought and paid for a complete complementary disk brake conversion for some lucky RVer. You've already got it jacked up and will be sitting there for several minutes SLOWLY pumping and spinning the tire … pushing the used grease out of the inner bearing right into the outer bearing hoping you didn't pop the wheel seal … awwww what the heck … do what you think best.
dieselguy is offline   Reply With Quote
Old 10-28-2018, 11:15 PM   #19
Graham
Established Member
 
Join Date: Apr 2010
Location: Kamloops
Posts: 37
M.O.C. #10287
Has Dexter suggested their flo thru lube system is faulty? I think you may have identified the reason failures have occurred, by forcing the grease in too fast and hard breaking the seals.
Graham is offline   Reply With Quote
Old 10-29-2018, 07:23 AM   #20
ChuckS
Montana Master
 
Join Date: Dec 2017
Location: Mountain Home
Posts: 772
M.O.C. #20949
If you don’t have the skill set to remove the wheel and hub and clean and repack yourself please take it to someone that does..

Just pumping in some more grease is doing nothing but giving you a feel good..you still have no idea what the brakes and hardware look like. And no idea what the overall condition of the spindle, races, bearings like ok like..
ChuckS is offline   Reply With Quote
Reply

Tags
lune, wheels

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Powered by vBadvanced CMPS v3.2.3
Disclaimer:

This website is not affiliated with or endorsed by Montana RV, Keystone RV Company or any of its affiliates. This is an independent, unofficial site.


All times are GMT -6. The time now is 09:07 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2023, vBulletin Solutions, Inc.