|
10-02-2022, 01:44 AM
|
#1
|
Established Member
Join Date: Aug 2022
Location: Sabinal
Posts: 34
M.O.C. #31462
|
Rebuilt steps
Another project done on this trailer
So the previous owners puppy chewed the carpet on the stairs. So they ripped the carpet off (and didn’t put steps back together right they had no support in the back of the first step). Anyway both steps had some give to them and my mother isn’t a small woman and I was concerned about safety. So when I bought it they had stapled a runner carpet on the steps. Was not a good job.
So I began and ripped off the bad carpet job. What do I find a worse tile job lol. They got cheap stick on tiles and tried putting them on plywood (doesn’t stick if you didn’t know). And it was horrible looked like a kindergartner collage. Not a single straight line lol it was ugly. So out they went.
Now I can see the factory steps and see the lack of support in the back of the first step causing it to give when your step on it. Looking at it I was still not happy. I took the steps apart to find they were made out of 1/4 inch plywood. I shook my head and said he’ll no.
So I rebuilt the steps. I used 1 inch tread boards and 3/4 risers. Then I decide to use some trim to make it look better.
I am disabled so it takes me a while to do things and these steps took me a bit. I wanted hardwood steps, no carpet. This meant I would have to learn how to stain lol.
So I cut the pieces for the main steps. And then used poly stain. Couple times I had to sand it back off and redo it because I didn’t like it. And it was funny cutting boards cause I would pick a part of the bird that had knots or cool patterns in the wood. Grain to give it character. And I put about 4-5 coats of stain on each piece.
Then I put the pieces in place and used a finish nailer to anchor them down. I had stained the trim boards though I had not cut them yet. I taped off the steps and stained again. Then I used on wood filler to do some minor filling. Then I cut trim and stained it. Then it was putting the trim on. Once the trim was in I used wood filler to fill in tops of nail holes. Then with it all together it was time to stain again.
And now it is finally done. It does take a lot of time and I learned a lot. Put the poly stain on in light coats. Poly stain is a pain to sand off. Something I didn’t know all sandpaper is not equal. I had some gator sandpaper from Walmart 60 grit. When I had to sand off poly stain it absolutely sucked. I was using electric hand sanders. Sheets didn’t last but a couple min and was not standing effectively. Then I had some 3m 100 grit purple sandpaper. Not this sandpaper worked GREAT. It may have been a finer grit but it was much more effective. I learned all sand paper is not equal. I will be using. 3m sandpaper from now on.
So anyway for the project I am very happy with how the steps came out. And they are so much sturdier than what was originally made.
So here are before and after pictures and I am very proud of how they came out.
|
|
|
10-02-2022, 06:57 AM
|
#2
|
Montana Master
Join Date: Dec 2021
Location: Northeast TX
Posts: 944
M.O.C. #30262
|
Steps look great! Even with a steep learning curve, there is just something satisfying to the soul when doing woodworking. Great job
__________________
Lee, Edith, Lil' Bit & Cuddles
22 MHC 331RL, Surge Guard 35550, SumoSprings, Kodiak disc brakes, 412Ah Lithium, Gen 3 Goosebox, Sailun 85s
22 Ram 3500 CC DRW 6.7 CTD Herrin Hauler Classic Bed, 45 gal AUX tank
|
|
|
10-02-2022, 07:16 AM
|
#3
|
Established Member
Join Date: Aug 2022
Location: Sabinal
Posts: 34
M.O.C. #31462
|
Thanks. It was a lot of work but I love the way they came out.
Yeah every time I finish a project i feel good about it. And this Rv hasn’t looked this good in a while, I knew the previous owners
|
|
|
10-02-2022, 11:30 AM
|
#4
|
Montana Master
Join Date: Oct 2018
Location: Anderson
Posts: 2,596
M.O.C. #22835
|
The steps came out looking real nice. You did a good job.
I've been doing carpentry and wood-working all my life. I've remodeled (completely) 4 different houses we've lived in and probably a dozen different houses (or rooms in a house) for close relatives, churches, and friends, and I've done a lot, I mean a lot, of Polyurethane finishing.
Just for a future reference ... when applying Polyurethane, do not do it with a brush. Take a sheet of paper towel (Scott's shop towels, as they do not leave lint), fold it up and dip it into the Polyurethane can and then wipe the Polyurethane onto the wood surface with the paper shop towel. It will go on extremely thin and very, very smooth. It also will dry fast too. When dry, put on a second coat exactly the same way, with a shop towel (not a brush). You will find you never have to sand between coats as all the little bumps and air bubbles are not there. When done, it will be smooth as glass.
I've been doing it this way for years now. I never use brushes any more. (paint, now that's different). But for Polyurethane, this is the best way to do it.
__________________
Who you are right now is a sum total off all you use to be.
2019 Montana High Country 375FL
2014 Chevy Silverado Duramax, 6.6L Dually
|
|
|
10-02-2022, 05:29 PM
|
#5
|
Established Member
Join Date: Aug 2022
Location: Sabinal
Posts: 34
M.O.C. #31462
|
This was stain and poly mixed together not staining and the poly. It was called polystain if I remember i can take a pic of the can
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|