|
05-01-2022, 06:23 AM
|
#1
|
Established Member
Join Date: Nov 2021
Location: Sarasota
Posts: 13
M.O.C. #30039
|
IN·command showing 41 degrees
Me and this in-command system has been battling since we took delivery 6 months ago. Last night set heat at a certain degree. Woke up drenched in sweat went out to control panel and the temperature inside was at 41 degrees. Tried shutting down abs restart no affect. Used the phone which is another battle altogether anyhow, using phone the temperature showed the assumed correct temperature. Went to control panel and it was showing the same. Scratched my head and set temp and set to electric low fan. This morning all seems to be good.
What happened? There were severe high winds last night…would that cause this? One forum said to turn battery disconnect and disconnect shore but Where us disconnect switch? Give me switches not a HAL. As with many many RV items I will chalk it up to experience. BUT temps are to be low 30’s again this week. Where is spring?
|
|
|
05-01-2022, 06:49 AM
|
#2
|
Montana Fan
Join Date: Aug 2020
Location: Aurora
Posts: 429
M.O.C. #26926
|
When I had a problem with the temps being wrong it was only one zone and was a loose wire on the sensor. When I removed the sensor from the wall it was spliced to the wire that carries the signal to the RTU (which is where the InCommand reads it). The splice was 2 tiny crimp wire nuts, I remade the connection with new tiny crimp wire nuts and all was good. I now carry spare sensors too.
Also, the wire from the sensor may or may not be spliced inside the roof top unit where the control board is - a bad connection will produce temp errors. Perhaps the winds shook something around up there and it "cured" itself as the wind died down.
__________________
Rip & Beth
2021 3121RL Legacy Cobalt FBP, MORryde IS & pin box
2020 F350 PSD CCLB SRW
|
|
|
05-01-2022, 10:28 AM
|
#3
|
Montana Master
Join Date: Dec 2007
Location: Kansas City, Missouri
Posts: 2,707
M.O.C. #7992
|
Quote:
Originally Posted by OnlyRoom42
Me and this in-command system has been battling since we took delivery 6 months ago. Last night set heat at a certain degree. Woke up drenched in sweat went out to control panel and the temperature inside was at 41 degrees. Tried shutting down abs restart no affect. Used the phone which is another battle altogether anyhow, using phone the temperature showed the assumed correct temperature. Went to control panel and it was showing the same. Scratched my head and set temp and set to electric low fan. This morning all seems to be good.
What happened? There were severe high winds last night…would that cause this? One forum said to turn battery disconnect and disconnect shore but Where us disconnect switch? Give me switches not a HAL. As with many many RV items I will chalk it up to experience. BUT temps are to be low 30’s again this week. Where is spring?
|
Man am I glad I don't have in command. Are you sure it didn't get switch from Fahrenheit to Celsius? 41C is 105 F
__________________
2006 3000RK
2009 Ram 2500
|
|
|
05-01-2022, 12:09 PM
|
#4
|
Site Team
Join Date: Oct 2005
Location: Carmichael - CA
Posts: 7,370
M.O.C. #4831
|
^^^^^^^^^^^^^^^^^^
__________________
Carl (n Susan)
There is more to life than fuel mileage.
2012 Montana 3700RL Big Sky Package towed by a 2015 Ford F350 6.7L PSD 4WD CC LWB
|
|
|
05-26-2022, 07:52 AM
|
#5
|
Established Member
Join Date: Nov 2021
Location: Sarasota
Posts: 13
M.O.C. #30039
|
Happened again
Two days ago the iN·command screen was blank. It appeared to shut itself down. Held pier button until it can on. This morning again the screen read 41 degrees Fahrenheit. Turned off. Phone app not helping this time. Upon start up the temp is showing “-F”. No temp.
Give me real buttons and thermostat. Don’t need some POS system that fails almost every week.(other issues as well).
Going to try power off and battery disconnect to reset the damn thing.
|
|
|
05-30-2022, 06:43 AM
|
#6
|
Montana Master
Join Date: Dec 2017
Location: Mountain Home
Posts: 839
M.O.C. #20949
|
Most likely the gateway for that Zone AC is failing. It is what communicates across the CANBUS to the roof AC units, furnace and BCM for the In Commamd tablet display.
The relays inside that gateway are nit working correctly and that is why yo7 are having issues.
It’s a known issue
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Disclaimer:
This website is not affiliated with or endorsed by Montana RV, Keystone RV Company or any of its affiliates. This is an independent, unofficial site.
All times are GMT -6. The time now is 08:48 PM.